When you turn on your PC, the processor attempts to begin the process of processing data. But, since the system memory is empty, the processor doesn't really have anything to execute, or even begin to know where to look for it. To ensure that the PC will always boot regardless of the BIOS code, both chip and BIOS manufacturers developed their code so that the processor, once turned on, always starts executing at the same place, FFFF0h.
Similarly, every hard disk must have a consistent "starting point" where key information is stored about the disk, such as the number of partitions and what type they are. There also must be someplace where the BIOS can load the initial boot program that starts the process of loading the operating system. The place where this information is stored is called the master boot record (MBR), also referred to as the master boot sector or even just the boot sector. Do not confuse the master boot sector with volume boot sectors, which are indeed different.
The master boot record is always located at cylinder 0, head 0, and sector 1, the first sector on the disk. This is the consistent starting point that the disk will always use. When a computer starts and the BIOS boots the machine, it will always look at this first sector for instructions and information on how to proceed with the boot process and load the operating system. The master boot record contains the following structures:
1. Master Partition Table: This small bit of code that is referred to as a table contains a complete description of the partitions that are contained on the hard disk. When the developers designed the size of this master partition table, they left just enough room for the description of four partitions, hence the four partition (four physical partitions) limit. For this reason, and no other, a hard disk may only have four true partitions, also called primary or physical partitions. Any additional partitions must be logical partitions that are linked to (or are part of) one of the primary partitions. One of these partitions is marked as active, indicating that it is the one that the computer should used to continue the boot process.
2. Master Boot Code: The master boot record is the small bit of computer code that the BIOS loads and executes to start the boot process. This code, when fully executed, transfers control to the boot program stored on the boot (active) partition to load the operating system.
Obviously, due to the great importance of the information stored in the master boot record, should it become damaged or corrupted in some way, serious data loss often occurs. The master boot code is the first program executed when you turn on your PC, and is often the target of a virus. In order to understand the Master Boot Record and the Master Boot Code buried within it, it might be helpful to understand the sequence of events that occur when your computer starts.
Although often overlooked as a diagnostic tool, the Boot Sequence performed by your computer can often tell you what may be wrong with the hardware itself should you be experiencing problems, even moderate ones. The following will take you through the System Boot sequence step by step. If you notice any thing unusual through each sequence of events, then you only need to look at the step where the delay appears to occur or back one step.
What occurs during the System Boot Sequence?
The system BIOS, a small bit of code inserted in the BIOS prom chip located on your computers motherboard, is what starts the computer running when you turn it on. Below we have outlined the typical sequence of events that occur during your computers startup process, although they will vary by the manufacturer of your hardware, BIOS, and the peripherals you have in the PC. Again, this is a typical sequence of events that occur when you turn on your computers power switch:
1. The internal power supply turns on, initializes and then takes a few moments to generate reliable power for the rest of the computer. If the power received by the motherboard's chipset, and subsequently the processor, is not within expected parameters, the chipset will generate a reset signal to the processor in the same fashion as if you were to touch the reset button. This will continue until the motherboard receives a Power Good signal from the power supply or you turn the system off because of a failed power supply.
2. After a Power Good signal is received, or after the reset button is released and there is confirmation of reliable power, the processor will be ready to start executing. When the processor first starts, it really has no idea what to do next as there is nothing at all in the memory to execute. Of course the processor designers are aware of this, so they pre-program the processor to always look at the same place in the system, the BIOS ROM, for the small bit of startup code to begin the boot process. This is typically located at memory location FFFF0h, or right at the end of the system memory. Developers locate it there in the event the size of the ROM has to be changed so as to prevent compatibility problems. Since there are only 16 bytes from there to the end of conventional memory area, this location contains just a "jump" instruction telling the processor where to go to find the real BIOS startup program.
3. The BIOS performs the power-on self test (POST). If there are any fatal errors, the boot process stops. If the POST is successful, the BIOS calls INT 19 (Interrupt 19) and then proceeds to look for devices attached to the motherboard.
4. The BIOS code begins its search by looking for a video card, more particularly, its looking for the video card's built in BIOS program, (normally found at location C000h in memory) and if found, runs it. The system BIOS executes the video card BIOS, which in turn initializes the video card. Most modern video cards will display information on the screen about the video card, which is why on some modern PC's you usually see something on the screen about the video card before you see the messages from the system BIOS itself.
5. Once video has been enabled, the BIOS begins searching for other devices that may have their own ROM and whether that ROM has its own BIOS code. Normally, the floppy drive is located at 0000:7C00, and the IDE/ATA hard disk BIOS will be found at C8000h. If a floppy and/or hard drive is found, their codes are executed. If, during this INT 19 process, any other device BIOS's are found, they are executed as well.
6. The BIOS displays its startup screen, which provides some key information about the BIOS as well as other system information.
7. As the boot sequence continues, the BIOS continues to perform additional tests on the system. Depending upon the system manufacturer, this will usually include a memory count. The BIOS will generally display an error message on the screen if it encounters an error when it counts installed memory. You will find these error messages and their explanations in our Support Center in the Motherboard and BIOS section or you can click here. (Clicking here will open a new window)
8. During the next phase of the BIOS startup process, it performs somewhat of an inventory of the hardware installed in the system, and then communicates or interrogates it to ensure that the hardware is functioning. Most modern BIOS's have automatic settings to collect information such as memory timing, based on what kind of memory it finds. Today's BIOS's dynamically set hard drive parameters and access modes, and will display a message on the screen for each drive they detect and configure in this way. It will also search for and label logical devices such as COM and LPT ports. Note: If the BIOS supports the Plug and Play standard, and the feature is enabled, this is the point at which it will detect and configure Plug and Play devices and display a message on the screen for each one found.
9. During the final phase of the POST and BIOS boot process, the BIOS will display a summary screen with your system's configuration. While early machines, 486 through Pentium II, were fairly accurate about the system configuration information, later machines using the later Pentium III and AMD processors can have some inaccurate information. This is usually related to BIOS setup issues involving processor information. Checking this data can be helpful in diagnosing setup problems, although it can be hard to see because sometimes it flashes on the screen and then scrolls off the top.
10. Once the BIOS finishes what it needs to do, it begins searching for a drive to boot an operating system. All BIOS's contain a setting that controls this search sequence for a boot drive. Most are set to first look for a bootable floppy disk, and if one is not found then proceed to a hard disk, which is usually the C: drive. Some BIOS's permit you to boot from your CD-ROM drive or other devices such as a SCSI (Small Computer System Interface), depending on the boot sequence selected. Once the BIOS identifies its target boot drive, the it looks for boot information to start the operating system boot process. If it is searching a hard disk, it looks for a master boot record at cylinder 0, head 0, sector 1, the first sector on the disk. If it is searching a floppy disk, it looks at the same address on the floppy disk for a volume boot sector.
11. Once the boot sector is found and its contents or data verified, the BIOS starts the process of booting the operating system by using the information in the boot sector. If this is a floppy disk boot sector, the information is read into memory at location 0000:7c00. INT 19 goes to memory location 0000:7c00 to continue the process. If no boot sector is found on the floppy drive, INT 19 moves to the next bootable drive in the list provided by the motherboard BIOS, usually a hard drive, and then attempts to read the MBR. If a Master Boot Record is found, it is read into memory at location 0000:7c00 and INT 19 jumps to memory location 0000:7c00 the same as was the case with the floppy. At this point, the BIOS attempts to move control of the computer from the BIOS to the actual operating system.
12. Next, the small program in the Master Boot Record will attempt to locate an active (bootable) partition in the hard drives partition table. If such a partition is found, the boot sector of that partition is also read into memory at location 0000:7C00 and then MBR program itself jumps to memory location 0000:7C00. Keep in mind that each operating system has its own boot sector format. The next step involves the small program in the boot sector locating the first part of the operating system's kernel loader program, or in some cases the kernel itself or perhaps a boot manager program, and read then that into memory. For you Windows NT and Windows 2000 fans, this kernel loader is referred to as NTLDR. You will find a description of the DOS boot process here.
13. If no boot device of any type can be found, the system will display an error message and stop. The specific error message is depends on the BIOS developer and/or the computer's manufacturer, and can be anything from a rather clear "No boot device" to the very cryptic "NO ROM BASIC - SYSTEM HALTED". This will also happen if you have a bootable hard disk partition but forget to set it active. Believe it or not, you can partition a drive, format it and install the operating system and never realize that there is problem until the first start of that operating system occurs.
This entire process is referred to as a "cold boot" (since the machine was off, or cold, when it started). A "warm boot" also known as a "soft boot" is the same thing except it occurs when the machine is rebooted using the Ctrl + Alt + Del keys. In this case the POST is skipped and the boot process continues at roughly step 8 above. As a side note, INT 19 is also called when the CTRL-ALT-DEL keys are used. On most systems, Ctrl + Alt + Del causes a soft-boot or shorten version of the POST to be executed before INT 19 is called.
Many things can damage the Master Boot Record, therefore it might be helpful for you to know where certain portions of the code reside in the MBR, should you have to recover the MBR manually.
You will find that:
* The MBR program code starts at offset 0000.
* The MBR messages start at offset 008b.
* The partition table starts at offset 01be.
* The signature is at offset 01fe.
Source: http://www.dewassoc.com/kbase/hard_drives/master_boot_record.htm
Posts
